INFINITY REFERENCE SERIES AMP 611A

Refer to the chart below to determine minimum wire-gauge size. Allows bass to pass through to the speakers; should be selected when powering subwoofers. Choosing a Location and Mounting the Amplifier Choose a mounting location in the trunk or cargo area where the amplifier will not be dam- aged by shifting cargo. Considering the features that this car woofer offers, it comes at a dirt cheap price for sure. Adjust the crossover frequency to limit bass, and provide increased system volume with less distortion. Figures 3 and 4 show how to configure the Reference subwoofer amplifiers models a, a and a. When using the low- or high-level inputs, the AUX outputs can be used to pass a full-range line-level signal to another amplifier.

See Figure 1 for connection location. Amplifier cooling is essential for proper amplifier operation. About this product Product Identifiers Brand. Minimum speaker load is 2 ohms. Refer to the chart below to determine minimum wire-gauge size. This will allow the subwoofer level to be adjusted from the listening position. For sealed enclosures, the DBO can be used to enhance the lower bass region of sealed enclosures. Reconnect the – negative lead to the vehi- cle’s battery.

Be sure to use appropriate grommets whenever routing wires through the firewall or other sheet metal. For simplicity, Figures 3 and 4 do not deries power, remote and input connections. For simplicity, Figures 10 through 12 do not show power, remote and input connections.

Contact Seller

Check speaker connections for proper polarity. Install the control module in the front of the vehicle within easy reach of the driver. Search the history of over billion web pages on the Internet. We recommend listening at low or moderate levels while driving your car. Both the underside of the dash and the center console are suitable locations. Amplifier may need service; see enclosed warranty card for service information. When using the low-level or high-level inputs, the AUX outputs can be used to pass a full-range line-level signal to another amplifier.

  DE CLUB VAN SINTERKLAAS EN HET GEHEIM VAN DE SPEELGOEDDOKTER CAST

Initially set the crossover-frequency control midway. Skip to main content. For vented enclosures, the DBO should be used as a serues filter to reduce overexcursion of the woofers. Do not install the fuse at this time.

Remember that the am; can extend behind the surface. Refer to “Troubleshooting” for specific indications. Connect the optional remote level control using the RJ jack on the side of the amplifier. IVIinimum speaker impedance for bridged operation is 4 ohms. The a, a and a amplifiers are not equipped with high-level inputs.

Make sure that the amplifier is mounted securely using nuts and bolts or the supplied mounting screws. So you need not worry about its malfunctioning as errors, if any, can be easily rectified under apm warranty period.

Power Connections The Reference amplifiers are capable of delivering high power levels, and require a reliable connection to the vehicle’s electrical system in order to perform optimally. Refer to the wmp instructions accompanying the lOOrc. Show More Show Less. Reference subwoofer amplifier with one woofer connection. If using the a or a to drive a subwoofer sset the crossover mode to LP low-pass. Amplifier cooling is essential for proper amplifier operation.

Considering the features that this car woofer offers, it comes at a dirt cheap price for sure. While listening to music, adjust the crossover for the least perceived distortion from the speakers, allowing them to reproduce as much bass as possible. Instead, please ask your authorized Infinity car audio dealer about professional installation.

Speakers are not connected properly. Although these instructions explain how to install Reference amplifiers in a general sense, they do not show specific installation methods that may be required for your particular vehicle.

  MGA ANAK NI FACIFICA FALAYFAY CAST

Infinity accepts no liability for hearing loss, bodily injury or property damage resulting from the use or misuse of this product. Figures 3 and 4 show how to configure the Reference subwoofer amplifiers models a, a and a.

Speaker connections should be made using a minimum of gauge wire. One of the major factors that compelled me to purchase this specific model is the price. To the right are two application diagrams to help plan your subwoofer system installation.

Disconnect the – negative lead from your refference battery.

Allows a full-range signal through to the speakers; can be used with larger full-range speakers such as 6″ x 9″s. Remove speaker leads one at a time to locate shorted speaker or wire, then repair.

Buy Infinity Reference A Car Amplifier online | eBay

Rfeerence you do not have the necessary tools or experience, do not attempt the installation your- self. Adjust the crossover frequency to limit bass, and provide increased system volume with less distortion. For simplicity, Figures 7 througin 9 do not show power, remote and input connections. When using the low- or high-level inputs, the AUX outputs can be used to pass a full-range line-level signal to another amplifier. Choosing a Location and Mounting the Amplifier Choose a mounting location in the trunk or cargo area where the amplifier will not be dam- aged by shifting cargo.

After the source unit is on, blue Infiinity on the top panel will light, indicating the amplifier is on. More items related to this product.